Sonic-alert Digital Program Controller DCP301 Bedienungsanleitung Seite 35
- Seite / 187
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 4. WIRING
4-3
4-2 Compensating Lead
In the case of thermocouple input, connect the bare thermocouple lead to the terminal. If the thermocouple is located
a long way from the DCP301 or the thermocouple is connected to a terminal, extend the connection using a compen-
sating lead and then connect to the terminal. Use shielded compensating leads only.
• For I/O other than thermocouples, use JCS-364 shielded instrument polyethylene insu-
lated vinyl sheath cable or equivalent product. (This is generally referred to “twisted
shielded cable for instruments.”) The following cables are recommended.
Fujikura Ltd. 2-core IPEV-S-0.9mm
2
x 1P
3-core ITEV-S-0.9mm
2
x 1T
Hitachi Cable Co. 2-core KPEV 0.9mm
2
x 1P
3-core KTEV-S-0.9mm
2
x 1T
• Shielded, multi-core microphone cord (MVVS) can be used if there is little electro-
magnetic induction.
- Digital Program Controller 1
- User’s Manual 1
- WARRANTY 2
- TECHNICAL ASSISTANCE 2
- SAFETY PRECAUTIONS 3
- Unpacking 6
- Contents 8
- Chapter 7. PARAMETER SETUP 10
- Chapter 8. PROGRAM SETUP 10
- Chapter 9. TROUBLESHOOTING 11
- Chapter 10 12
- SPECIFICATIONS 12
- Chapter 11. CALIBRATION 12
- RUN/HOLD 13
- 1-1 Features 14
- 1-2 Basic Function Blocks 15
- 1-3 Data Structure 16
- 1-4 System Configuration 17
- 1-5 Model Numbers 18
- 2-1 Structure 19
- 2-2 Console 20
- Basic display state 22
- ■ Loader jack 25
- 2-3 Input Type and Range No 26
- Chapter 3. MOUNTING 28
- 3-2 Panel Cutout Dimensions 29
- 3-3 Mounting 30
- ■ Dust-proof cover 31
- ■ Mounting method 32
- 4-1 Wiring Precautions 33
- 4-2 Compensating Lead 35
- 4-3 Terminal Connections 36
- Direction 37
- ■ Power supply 38
- ■ Ground 38
- Chapter 4. WIRING 39
- ■ Connecting input 1 40
- ■ RS-485 interface 48
- Digital circuit 51
- 5-1 Data 52
- 5-2 Program Patterns 53
- ■ Events 1 to 3 54
- Chapter 5. FUNCTIONS 55
- ■ Time events 1 to 5 57
- ■ G.Soak (guarantee soak) 59
- ■ PID set selection 59
- (1)' 60
- (1)" 60
- ■ Pattern link 61
- 5-3 Modes 62
- ■ Mode transition 64
- ■ Mode transition operations 65
- ■ Mode transition limitations 66
- 5-4 Controller and Programmer 67
- ■ Control output 69
- ● 2G output 71
- ● 3D, 5K outputs 72
- MANUAL mode 72
- ■ SP output 73
- ■ Auxiliary output 73
- 6-1 Turning the Power ON 74
- Chapter 6. OPERATION 75
- Motor valve opening (%) 79
- Output state of events 1 to 3 79
- 6-3 Program Selection 80
- ■ Program selection 82
- ■ Read timing 83
- ■ Manual operation 84
- ■ Auto-tuning (AT) 84
- 7-1 Parameter Setup 86
- 7-2 How to Use 89
- 7-3 Parameter Setup List 92
- Handling Precautions 100
- E T 1 0 103
- E D 1 0 103
- H Y S 1 5 103
- D L 1 0 103
- PID Set No. Designated in the 108
- Program or Zone No. According 108
- ■ Setup data settings “S E t” 112
- SSR' 120
- q 0 (Special functions) 122
- Short-circuit 123
- ■ Table data settings “T B L” 125
- MV upper limit (CH1) 127
- I N S .” blinking 129
- d E L .” blinking 129
- C L R .” blinking 129
- ■ Programming map 131
- ■ Setting up pattern items 132
- ■ Display details 132
- Program No. Segment No 133
- ■ Setting up PV start items 138
- ■ Setting up cycle items 138
- P.L I N 139
- Program No 141
- Copy destination program No 141
- G .R E S 142
- ■ Alarm code display 144
- ■ Alarm categories 144
- 9-4 Replacing the Battery 152
- Comes out towards you 153
- Key cover 153
- Lock screw 153
- Connector 154
- RAM board 154
- (approx. 3cm x 8cm) 154
- Gray holder 155
- 10-1 Specifications 156
- Chapter 10. SPECIFICATIONS 157
- 25 ) and 157
- Item Specification 157
- ■ Accessories/option list 162
- 10-2 External Dimensions 163
- Chapter 11. CALIBRATION 166
- 4.0.4.4 169
- 2.0.2.2 169
- 11-2 Calibration Procedures 170
- ■Function test 171
- 1.0.1.1 174
- Table 11-11 175
- ■Current output calibration 176
- 11-3 Set Up 177
- Programming Map 179
- SAFETY REQUIREMENTS 180
- Revision History 184
- HONEYWELL SERVICE CENTERS 185
- No. CP-UM-5093E 187
Verwandte Produkte und Handbücher für Uhr Sonic-alert Digital Program Controller DCP301
Uhr Sonic-alert SB200ss Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Uhr Sonic-alert SBP100 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Uhr Sonic-alert SB300SS Bedienungsanleitung
(2 Seiten)
(2 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern